SC Hydraulic Engineering L3 Compact Liquid Pumps

SC Hydraulic Engineering L3 Compact Liquid Pumps is a leading manufacturer and designer of an ever growing line of high pressure, air-driven liquid pumps, as well as air and gas boosters which are being used in a variety of industries and applications.

Growing since 1953, we offer liquid pressures as high as 65,000 psig and can exceed 17,000 psig in gas pressures.

Product Information

PORTABLE
ECONOMICAL
LIGHTWEIGHT
REQUIRES NO LUBRICATION
EASY TO INSTALL & OPERATE
IDEAL FOR OEM APPLICATIONS

SC air-driven compact liquid pumps operate on the principle of differential areas. An air piston drives a smaller diameter hydraulic plunger to provide a pressure ratio. The pressure ratio determines the maximum outlet pressure. SC compact liquid pumps cycle automatically. When compressed air is first applied to the pump, it will cycle at its maximum speed producing maximum flow. At this stage, the pump is acting as a transfer pump filling the pressure receiver with liquid. The pump will then gradually start to cycle at a slower rate as the pressure in the receiver increases and offers more resistance to the reciprocating differential piston.

SC pumps stop automatically when the output pressure force and the air drive force is balanced to create a stall condition. At this point, the pump will maintain pressure without energy consumption, thus providing an economical source for hydraulic power. SC pumps will cycle with a slight drop in the outlet pressure or an increase in the air drive pressure due to very low frictional resistance. SC pumps are suitable for use on scissor jack lifts, aircraft jacks, clamping devices, punches and pin presses, valve actuation, roller tensioning, torque wrenches, press system overload, pressure testing, crimping, trash compactors, paper and printing paper cutters.

Compatible with all hydraulic fluids, plain water, distilled and di-ionized water, solvents, mild chemicals and liquefied CO2. 316 Stainless steel wetted hydraulic construction, lightweight (six pounds), 3.5″ x 7.00″ body includes inlet and exhaust muffler. Available in eight ratios: 15, 25, 35, 45, 65, 105, 125 and 195. Requires less than 15 psi air drive pressure to operate, the L3 series pump is self-priming for immediate operation. Maximum air drive pressure is 125 psi (intermittent duty) Can supply pressures up to 24,375 psi @ 125 psi air drive and flow rates up to 1.0 gpm.

Requires no electrical power or connections. Alternative gases that can drive the pump include nitrogen vapor from the liquefied gas or natural gas pipeline, thus offering a completely self-contained package independent of external power sources. The hand pump attachment option allows for manual operation when shop air is not available or for precision pressure control.

Application

Crimping
Valve actuation
Pressure testing
Torque wrenches
Clamping devices
Trash compactors
Well Control Panels
Press system overload
Punches and pin presses
Roller and bolt tensioning
Scissor jack lifts, aircraft jacks

Dimension

Dimensions

Dash	Actual	Max Pressure	Displacement	NPT/LF4 (Std)		SAE/LF4 (Optional)			C	D	L
Number	Ratio	psig @125 Pa (1)	Per Cycle	A Thread	B Thread	A Thread	B Thread	B Thread
			Cu. In.
-15	20	2,25	0.27	3/8″	1/4″	-8 SAE	-6 SAE	7/16-20 *	1.5	2.43	8.02
-25	31	3,5	0.18	3/8″	1/4″	-8 SAE	-6 SAE	7/16-20 *	1.5	2.43	8.02
-35	40	4,375	0.14	3/8″	1/4″	-8 SAE	-6 SAE	7/16-20 *	1.5	2.43	8.02
-45	55	6,125	0.1	3/8″	1/4″	-8 SAE	-6 SAE	7/16-20 *	1.5	2.43	8.02
-65	79	8,875	0.069	1/4″	1/4″	-6 SAE	-6 SAE	7/16-20 *	1	1.93	7.52
-105	123	14	0.044	1/4″	1/4″	-6 SAE	-6 SAE	7/16-20 *	1	1.93	7.52
-125	138	15,6	0.044	1/4″	7/16-20 *	-6 SAE	–	–	1	1.93	7.52
-195	213	24,375	0.038	3/8″	9/16-18	–	–	–	2.24	2.71	8.75

Ordering

Ordering Code

TABLE 1	Pump Series Designation (1)
L3	Compact Pump Stainless Steel Hydraulic Section
L3C	Compact pump Carbon Steel Hydraulic Section
TABLE 2	Seal Compound – Hydraulic Section
Blank	Std- Buna-N O-rings, UHMWP/CG-PTFE Main Seal (3)
Blank	Std- Buna-N O-rings, Polyurethane Main Seal
03	EPR O-rings, Polyurethane Main Seal
04	Viton O-rings, Polyurethane Main Seal
TABLE 3	Modifications
Blank	Standard – No Modifications
M002	Remote Pilot
M003	SAE Straight Thread Ports
M004	Hand Pump Attachment
M005	Distance Piece—Isolator
M006	No Air Piston Return Spring
M008	Noise Reduction
M009	7/16″-20 x 1/4″ High Pressure Fitting Outlet
M011	7/16-20 x ¼” Mounting Holes
M027	Hand Pump Attachment – 195 Ratio
TABLE 4	Actual Pressure Ratio (1)
Blank	Standard – No Modifications
15	20:1 Actual Ratio
25	31:1 Actual Ratio
35	40:1 Actual Ratio
45	55:1 Actual Ratio
65	79:1 Actual Ratio
105	123:1 Actual Ratio
125	133:1 Actual Ratio
195	213:1 Actual Ratio

Notes:

Do not fill gap on a two digit description
Additional Special Modifications may be included with an “M” suffix at the end of the model number.
Available only for L3-195

Performance Chart

Modification

M002 – Remote Pilot: This option provides for a separate 1/8″ NPT external air to pilot cycling valve. Useful for remote control operation of the pump.

M003 – Straight Threads: The straight thread modification offers the fluid inlet and outlet ports with SAE straight thread options.

M004 & M027 – Integral Hand Pump Attachment: This modification permits supplementary operation of the pump by hand. Useful in precise testing or emergency backup applications requiring a hand pump in addition to pneumatic power.M005 – Distance Piece: The distance piece models are furnished with an isolator attachment which prevents the hydraulic piston from retracting into the air drive during operation, thus providing 100% separation of the hydraulic assembly from the air drive assembly. The isolator attachment prevents contamination and acts as a heat barrier.

M006 – No Air Piston Return Spring: This modification provides improved fill on the suction stroke when pumping liquefied gases such as CO2.M008 – Noise Reduction: Noise reduction incorporates a special internal bumper allowing the pump to run quieter without impairing performance.M009 – 1/4″ O.D. High-Pressure Tubing Fluid Outlet: This modification provides a coned and threaded high-pressure connection for 20 KSI 1/4″ O.D. tubing (7/16-20 thread LF4 connection).M011 – Mounting Holes: Tapped and threaded bottom mounting holes are available for tank top mounting applications.

Source: schydraulic.com

Indonesia Marine Equipment

INAMEQ is provide all marine product (equipment and sparepart) and news about marine product to help procurement team at shipping industry, ship contractor, port contractor and oil gas company finding competitive price to directly connect with manufacturer and authorized local and international.