Windlass seating :- The forces acting on the windlass when the ship is anchored is much more than the mass of the windlass and hence has to be specially strengthened, the details of which are as described under and illustrated by sketch below.
The deck plating at forecastle and main deck in forecastle space scantlings.
The windlass is mounted on a doubler plate welded to the forecastle deck.
The deck girders in forecastle space is increased in The deck beams pitch distance decreased to accommodate more beams.
Four round pillars at four corners of the base of windlass doubler plate connect to the main deck plating to give continuity of strength to deck.
The windlass machinery is combined with the forward mooring winch as one unit. The main winch consists of a double reduction gearing arrangement to produce a large torque.
The windlass is arranged on a further reduction arrangement. The windlass part consists of a solid cable lifter wheel combined with the brake wheel keyed to a shaft properly supported on two bearings with its clutch arrangement. The clutch connects the cable lifter to driving gear when the anchor has to be hauled up.
For anchoring purpose the clutch is released with the cable ;lifter in braked position. When the anchor has to be dropped, the brake is released and the anchor along with the chain drops by gravity so that it strikes the ground with sufficient force to get entrenched in the mud. The sketch of the wind lass part is as given under.
Electrically operated windlass
The windlass including mooring winch machinery is common for both hydraulically operated or electrically operated equipment. In the case of the electrically operated windlass cum mooring winch the driving motor is a two speed motor controlled by a suitable pole changing device. The lower speed gives higher torque suitable for the initial breaking of the anchor from the ground when more force is required and the design torque provided for this condition is 150% of the full continuous torque for a period of at least 30 minutes. All three phase induction motors are steady speed motors with a small variation of load torque. The speed is fairly high since the frequency is high and to reduce the operating speed electrically is inconvenient since it involves increasing the number of pairs of poles. To avoid this a double reduction gear box with oil lubricated machine cut gears has to be incorporated in this system. As per class rules an over load slip clutch has also to be included for safety, since electrical safety cut outs are time based and may not cut out when overload happens suddenly. For these reasons the electrically operated windlass and mooring winch has its limitations and are used only on small ships.
The hydraulically operated windlass has larger torque capacities because the hydraulic motor can operate at very low speeds even at 5 to 10 rpm, there by building a very high torque. The torque –speed characteristics of hydraulic system is much better and flexible than electrical systems. Their comparison is shown in the sketch given under.
The Hydraulic machine is robust and can withstand a lot of shock. The components are less since the double reduction gear box and the slip clutch are eliminated thereby reducing the cost of the machinery. For safety a spring loaded shock valve is provided in the system which will connect the high pressure to the low pressure side when overload occurs. The hydraulic windlass cum mooring winch is illustrated below.
The hydraulic system schematic sketch below is illustrated as The main components of this system consists of the following :
- An expansion tank located on the forecastle deck to give a good head to the oil to flow.
- The gear pump located in the forecastle.
- The oil storage tank located in the fore castle store with attached hand pump to transfer oil to the expansion tank.
- The hydraulic motor mounted on the windlass frame and connected to the primary driving The control block is integral with the motor casing and cut sectional sketch of the motor is illustrated separately.
When the control block is placed in the neutral position the oil flow to the motor is prevented by the blanked connection in the block in this position. When the block is shifted to no 1 position only two paths are connected and the flow quantity being moderate it gives the rated speed and torque. When it is shifted to the 2nd position the oil flow has 4 paths and this conforms to the higher torque and speed rating. This position is used for breaking the anchor hold in the ground and when free the block can be used for lifting the anchor along with chain When the block is shifted to the upper R position the passages in the block are crossed causing the flow of oil in reverse direction thereby turning the motor in the reverse direction.
For mooring winch operations no 1 and R positions are used as convenient. For normal anchor lifting no 1 position is used. For walking back the anchor R position is used. For breaking anchor from ground no 2 position is used.
When changing over from 1 to 2 more oil is required and this is provided by oil flow from expansion tank to pump through a non return valve. When changing over from 2 to 1 excess oil from system flows back into expansion tank by another non- return valve.
The motor is simple in construction at the same time it is robust and can take a lot of rough handling. The rotor is a thick disc with rectangular slots cut on the circumference. Each slot accommodating a thick vane held in place by the cover plate. The vanes are made to press hard on the casing (internal) surface by a bow spring held under the vane.
The rotor is mounted on a strong roller bearing and also carries an oil seal which prevents leakage of oil during operation.
During lay ups at special surveys, the end cover is opened up and vanes as well as springs which are damaged are renewed. The oil seal and roller bearing also renewed if they are worn out. The sketch of the winch motor with detail of vane assembly is shown under.
The electric motor driving the gear pump is a three phase double squirrel cage motor with high slip capability combined with higher rotor current capacity because of the two layers (radially) of copper bars embedded in the iron rotor. The sketch of this rotor is reproduced as under.
Read more : Common mooring methods used for marine