Windlass Maintenance On Ships

Ship Anchor Windlass

WINDLASS

  • Windlass seating :- The forces  acting  on  the  windlass when  the  ship  is  anchored  is  much  more  than  the  mass  of  the  windlass  and  hence has  to  be  specially  strengthened,  the  details  of  which  are  as  described  under  and  illustrated  by  sketch below.

  • The  deck plating at forecastle  and  main deck  in  forecastle  space scantlings.

  • The windlass is  mounted on  a  doubler  plate welded  to  the  forecastle  deck.

  • The deck girders in forecastle space  is increased in The  deck beams  pitch distance  decreased to  accommodate  more  beams.

  • Four  round  pillars  at  four corners  of  the  base of  windlass  doubler  plate  connect  to  the  main  deck  plating  to  give  continuity  of  strength  to  deck.

The  windlass   machinery  is  combined  with  the  forward  mooring  winch  as  one  unit. The  main  winch  consists  of  a  double  reduction  gearing  arrangement  to  produce  a large  torque.

The  windlass  is  arranged  on  a  further  reduction  arrangement. The windlass  part  consists  of  a  solid  cable  lifter  wheel combined  with  the  brake  wheel keyed to a shaft  properly  supported  on  two  bearings  with  its  clutch  arrangement. The  clutch  connects  the  cable  lifter to   driving  gear  when  the  anchor  has  to  be  hauled  up.

For  anchoring  purpose  the  clutch  is  released with  the  cable  ;lifter  in  braked  position. When  the  anchor  has  to  be  dropped,  the  brake  is  released and  the  anchor  along  with  the  chain  drops  by  gravity so  that  it  strikes  the  ground  with  sufficient  force  to  get  entrenched  in  the  mud. The  sketch  of  the  wind  lass  part  is  as  given  under.

Windlass Maintenance On Ships

Most of the windlasses found onboard ships these days are driven directly by electric motors or by pressurised hydraulic oil.

They cater to hoisting up varying loads with the help of gear and teeth arrangement. The major parts of a windlass are main shaft, driving shaft, inspection cover, gear, gear frame, drums (one or more), warping head or couplings, brake band, brake liner assembly, chain wheel, gear wheel, pinion, clutch and high speed low speed hydraulic valve blocks.

Regular inspection of external and moving parts of gear and shaft enables a ship’s officer to judge the wear and amount of use of this important machinery.

While using windlass for hoisting, an early indication can be temperature rise on the exterior of hydraulic pipe lines driving the main shaft. This further needs to be investigated for the correct technical specification and properties of the oil used and load  on the motors and working pressure of  the driving hydraulic oil. The bearing, pin and sliding parts of the assembly require a special grease recommended to be used on open gears to prevent them from weather damage as well. Often the maintenance routines for the filters of the hydraulic pumps used for running windlasses are followed by ship’s staff. The oil samples are also collected periodically for analysis.

The main shaft or gear shaft too may be checked for temperature rise to indicate lack of or less lubrication than required. The main shaft extends outside the gear frame and is equipped with drums, warping heads or cable lifter unit. The shaft consists of shaft and pinion and shaft roller bearing, which is lubricated through the grease nipple.

The drums are usually provided with manual brakes or they can be hydraulic operated brakes. Brakes are provided with foundation plate welded to the deck.

Often windlass shaft is coupled with mooring winch and it is important to put the mooring winch brake ‘on’ and the clutch in disengage position for the winch before operating the windlass.

When anchoring speed is high the anchor runs away and the brake lining might get damaged due to heat. Thus dropping the anchor and repeating the drop and stoppage at every ½ shackle is advisable to prevent damages to brake liner due to temperature rise.

In rough weather it is necessary to loosen the anchor chain tension while heaving up by using engines to avoid excessive load on the windlass. In case excessive load is applied on the windlass while heaving, bring the operating lever to neutral position then pay out the cable little bit, increase engine revolutions and heave the chain again once the load reduces. Speed change for windlass from high to low will cause large speed change and thus they are constructed with utmost safety features.

A weekly schedule for windlass should involve lubricating all the plain bearings through the grease nipples and the gear teeth. Monthly or quarterly checks recommended for the condition of brake linings should be carried out depending on the frequency of use. Monthly routines should include all the couplings, hydraulic valves and piping to be checked for leaks, tightness and functioning. Covering couplings with anti corrosive tapes can prevent them from getting rusted. The hydraulic motor foundation to be checked for tightness and any sign of wear at the base.

On an yearly basis the bearing clearances, gear wheel contact areas and hydraulic valves to be adjusted for correct operating pressure. The bolts and nuts should be checked for proper tightness. The gear contact should be at least 70% or more failing which the gear wheel gives abnormal noise. Preventive actions can be greasing of gear teeth or the realignment of windlass.

Adjustment of brake settings of windlass : When the brake lining has worn away it can be adjusted to render the necessary holding force. Often manufacturer’s recommend after a specific reduction in thickness of the brake lining to replace it with new one. However, when the liner thickness reduces within the limits applicable, brake setting can be adjusted with the regulating screw as a makeshift measure. Both the linings, upper and lower should be changed at the same time.

Adjustment of brake settings of windlass

During liner replacement it is very important to secure the chain and anchor with extra lashings if the ship’s staff is carrying out this job at sea. The job should preferably be carried out in calm waters without any uneven rolling or pitching. When the anchor and chain is secured by the stopper and extra lashings the brake assembly can be checked. For that the brake has to be fully opened and all the pins connecting to the brake has to move smoothly, cleaning, greasing or hammering of pins may be required for this purpose. The brake nut can be used to adjust the length of brake spindle which in turn corresponds to the liner thickness.

It is very important that while replacing the brake liner assembly of a windlass the position of the brake screw down lever and  position of brake bands corresponding to the brake position is marked. As after replacing the liner misalignments are often observed while reassembling the whole unit.

The spherical roller bearings assembled to the main shaft  are precision built and care must be taken while removing them. If any roller bearings fail it should be completely replaced. Never strike a roller bearing with a steel hammer. A wood hammer or soft hammer should be used to strike it lightly.

Read more : Planning and operational guidance for anchor ship

Advertisements
Advertisements
About Indonesia Marine Equipment 1349 Articles
INAMEQ is provide all marine product (equipment and sparepart) and news about marine product to help procurement team at shipping industry, ship contractor, port contractor and oil gas company finding competitive price to directly connect with manufacturer and authorized local and international.

Be the first to comment

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.